این سایت در حال حاضر پشتیبانی نمی شود و امکان دارد داده های نشریات بروز نباشند
Nanomedicine Journal، جلد ۷، شماره ۲، صفحات ۱۳۸-۱۴۸
عنوان فارسی
چکیده فارسی مقاله
کلیدواژه‌های فارسی مقاله
عنوان انگلیسی A novel three-dimensional printing of electroconductive scaffolds for bone cancer therapy application
چکیده انگلیسی مقاله Objective(s): Tissue engineering aims to achieve a tissue, which has highly interconnected porous microstructure concurrent with appropriate mechanical and biological properties. Materials and Methods: Therefore, the microstructure scaffolds are of great importance in this field. In the present study, an electroconductive poly-lactic acid (EC-PLA) filament used to fabricate a porous bone scaffold. For scaffolds model designed, solid-work software was used. Then, the designed modeled was transferred to simplify 3D to laminated with its G-Code file for fused deposition modeling (FDM) printer to create a scaffold with porosity around 65-75%. Two different shapes were designed and fabricated (cylindrical and cubic shape). The samples were coated with hydroxyapatite (HA) nanoparticle to enhance its chemical stability. In this study, the X-ray diffraction (XRD) confirmed that the EC-PLA is non-crystalized and scanning electron microscopy (SEM) used to present the apatite formation on the surface of porous scaffolds. The compression test, fracture toughness, and hardness were measured. The biological response in the physiological saline was performed to determine the rate of degradation of EC-PLA in phosphate buffer saline (PBS) and the apatite formation in the simulated body fluid (SBF) after 14 days. Results: Finally, the biocompatibility of the porous architecture was monitored using human gum (HuGu) cells. The ABAQUS modeling simulation was used to compare the experimental and analytical results. The obtained results showed that by applying force to both cylindrical and cubic scaffold, the Von Mises Stress (VMS) could withstand the scaffold mentioned above at 9.7-11 MPa. Conclusion: Therefore, it can be concluded that prepared porous scaffolds have a high potential in bone tissue engineering and probably the treatment of tumor-related bone defects as photothermal therapy. The porous EC-PLA scaffold was successfully fabricated and showed appropriate compressive strength (39.14 MPa), with controllable porosity of 60-70 %, which is a suitable candidate for replacing in bone tissues.
کلیدواژه‌های انگلیسی مقاله
نویسندگان مقاله | Marjan Monshi
Advanced Materials Research Centre, Department of Materials Science and Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran


| Saeid Esmaeili
Mechanical Engineering Department, Khomeinishahr Branch, Islamic Azad University, Khomeinishahr, Iran


| Amin Kolooshani
Mechanical Engineering Department, Khomeinishahr Branch, Islamic Azad University, Khomeinishahr, Iran


| Bahareh Kamyab Moghadas
Department of Chemical Engineering, Shiraz Branch, Islamic Azad University, Shiraz, Iran


| Saeed Saber-Samandari
New Technologies Research Center, Amirkabir University of Technology, Tehran, 15875-4413, Iran


| Amirsalar Khandan
New Technologies Research Center, Amirkabir University of Technology, Tehran, 15875-4413, Iran
نشانی اینترنتی http://nmj.mums.ac.ir/article_15125.html
فایل مقاله اشکال در دسترسی به فایل - ./files/site1/rds_journals/295/article-295-2318383.pdf
کد مقاله (doi)
زبان مقاله منتشر شده en
موضوعات مقاله منتشر شده
نوع مقاله منتشر شده مقاله پژوهشی
برگشت به: صفحه اول پایگاه   |   نسخه مرتبط   |   نشریه مرتبط   |   فهرست نشریات