این سایت در حال حاضر پشتیبانی نمی شود و امکان دارد داده های نشریات بروز نباشند
ژئوفیزیک ایران، جلد ۹، شماره ۵، صفحات ۵۷-۷۱
عنوان فارسی Application of surface-derived attributes in determining boundaries of potential-field sources
چکیده فارسی مقاله This paper describes an edge detection method based on surface-derived attributes. The surface-derived attributes are widely used in the interpretation ofseismic datain two main categories: (1) derivative attributes including the dip angle and the azimuth; (2) derivative attributes including curvature attributes.    In general, the magnitude of the normal curvature of a surface (curvature attributes) can be expressed in terms of derivatives of that surface which are called the first and second fundamental forms of the surface. For a quadratic surface which fits data, it is shown that the dip-angle equation in the interpretation of the seismic data is similar to the horizontal gradient magnitude (HGM) equation in the interpretation of potential field data. Among the infinite number of curvature attributes, a few of them which are suitable for edge detection are shown. The coefficients of a quadratic surface are calculated using the least square method. At a particular point, the attributes are obtained using these coefficients. Zero contours of most positive curvature and the determinant of the curvature matrix delineate the location of the edges of anomalies. Theshape indexattributequantitatively reflects the local shape of the surface over sources in terms of cap, dome, ridge, saddle, rut, trough and cup.Here, the maximum curvature is introduced as a new technique to detect the horizontal location of anomalies.    First, the introduced attributes were applied to the noise-free synthetic data. Then, the data with the noise added were used to check the stability of the method. In the presence of high-level noise, this method was successful in determining boundaries of the anomalies.Zero contoursof the most positive curvature, the determinant of curvature matrix and the maximum curvature properly illustratethe linear features within the mapped surface. The results of using surface-derived attributes were compared with tilt angle and HGM filters. This comparison showed that zero contours of the most positive and maximum curvature attributes are approximately matched with zero contours of the tilt angle and maximum values of HGM. Finally, this method was used for real data from Mobrun massive sulfide ore of Canada.MATLAB softwarewas used for programming and calculating the required parameters of this method.
کلیدواژه‌های فارسی مقاله Surface-derived attributes، potential field data، most positive curvature، Maximum Curvature، Shape Index، zero contours،
عنوان انگلیسی Application of surface-derived attributes in determining boundaries of potential-field sources
چکیده انگلیسی مقاله This paper describes an edge detection method based on surface-derived attributes. The surface-derived attributes are widely used in the interpretation ofseismic datain two main categories: (1) derivative attributes including the dip angle and the azimuth; (2) derivative attributes including curvature attributes.    In general, the magnitude of the normal curvature of a surface (curvature attributes) can be expressed in terms of derivatives of that surface which are called the first and second fundamental forms of the surface. For a quadratic surface which fits data, it is shown that the dip-angle equation in the interpretation of the seismic data is similar to the horizontal gradient magnitude (HGM) equation in the interpretation of potential field data. Among the infinite number of curvature attributes, a few of them which are suitable for edge detection are shown. The coefficients of a quadratic surface are calculated using the least square method. At a particular point, the attributes are obtained using these coefficients. Zero contours of most positive curvature and the determinant of the curvature matrix delineate the location of the edges of anomalies. Theshape indexattributequantitatively reflects the local shape of the surface over sources in terms of cap, dome, ridge, saddle, rut, trough and cup.Here, the maximum curvature is introduced as a new technique to detect the horizontal location of anomalies.    First, the introduced attributes were applied to the noise-free synthetic data. Then, the data with the noise added were used to check the stability of the method. In the presence of high-level noise, this method was successful in determining boundaries of the anomalies.Zero contoursof the most positive curvature, the determinant of curvature matrix and the maximum curvature properly illustratethe linear features within the mapped surface. The results of using surface-derived attributes were compared with tilt angle and HGM filters. This comparison showed that zero contours of the most positive and maximum curvature attributes are approximately matched with zero contours of the tilt angle and maximum values of HGM. Finally, this method was used for real data from Mobrun massive sulfide ore of Canada.MATLAB softwarewas used for programming and calculating the required parameters of this method.
کلیدواژه‌های انگلیسی مقاله Surface-derived attributes, potential field data, most positive curvature, Maximum Curvature, Shape Index, zero contours
نویسندگان مقاله محمد برازش |
institute of geophysics, university of tehran, iran
سازمان اصلی تایید شده: دانشگاه تهران (Tehran university)

سید هانی متولی عنبران | seyed hani motavalli anbaran
institute of geophysics, university of tehran, iran
سازمان اصلی تایید شده: دانشگاه تهران (Tehran university)

حجت قربانیان |
institute of geophysics, university of tehran, iran
سازمان اصلی تایید شده: دانشگاه تهران (Tehran university)

نشانی اینترنتی http://www.ijgeophysics.ir/article_33614_7e47b6607eaf57618a0c495ffc5c5840.pdf
فایل مقاله اشکال در دسترسی به فایل - ./files/site1/rds_journals/1514/article-1514-427694.pdf
کد مقاله (doi)
زبان مقاله منتشر شده fa
موضوعات مقاله منتشر شده
نوع مقاله منتشر شده
برگشت به: صفحه اول پایگاه   |   نسخه مرتبط   |   نشریه مرتبط   |   فهرست نشریات