این سایت در حال حاضر پشتیبانی نمی شود و امکان دارد داده های نشریات بروز نباشند
Dental Research Journal، جلد ۱۲، شماره ۲، صفحات ۰-۰
عنوان فارسی
چکیده فارسی مقاله
کلیدواژه‌های فارسی مقاله
عنوان انگلیسی Kinetics of pulpal temperature rise during light curing of 6 bonding agents from different generations, using light emitting diode and quartz-tungsten-halogen units: An in-vitro simulation
چکیده انگلیسی مقاله Background: Application of bonding agents (BA) into deep cavities and light curing them might increase pulpal temperature and threaten its health. The purpose of this study was to evaluate temperature rise of pulp by light curing six BA using two different light curing units (LCU), through a dent in wall of 0.5 mm. Materials and Methods: This in vitro experiment was carried out on 96 slices of the same number of human third molars (6 BAs × 2 LCUs × 8 specimens in each group). There were 6 groups of BAs: N Bond, G-Bond, OptiBond XTR, Clearfi l SE, Adper Single Bond 2 and V Bond. Each group of BA ( n = 16) had two subgroups of light emitting diode (LED) and quartz-tungstenhalogen light cure units ( n = 8). Each of these 16 specimens were subjected to light emitting for 20 s, once without any BAs (control) and later when a BA was applied to surface of disk. Temperature rises in 140 s were evaluated. Their mean temperature change in fi rst 20 s were calculated and analyzed using two-way repeated-measures and one-way analysis of variance (ANOVA) and Tukey (α = 0.05). Furthermore rate of temperature increase was calculated for each material and LCU. Results: Minimum and maximum temperature rises in all subgroups were 1.7 and 2.8°C, respectively. Repeated measures ANOVA showed that both of adhesive and LCU types had signifi cant effect on temperature rise after application of adhesives. Tukey post-hoc analysis showed Clearfi l SE showed signifi cantly higher temperature rise in comparison with Adper Single bond 2 ( P = 0.047) and N Bond ( P = 0.038). Temperature rose in a linear fashion during fi rst 30-40 s and after that it was non-linear. Conclusion: 20 s of light curing seems safe for pulpal health (with critical threshold of 5.5°C). However, in longer durations and especially when using LED units, the process should be broken to two sessions. Key Words: Composite resins, dental materials, differential thermal analysis, polymerization
کلیدواژه‌های انگلیسی مقاله
نویسندگان مقاله نجمه خاتون khaksaran | najmeh khatoon khaksaran


طاهره جعفرزاده کاشی | tahereh jafarzadeh kashi


وحید رخشان | vahid rakhshan


زهرا سادات زین العابدین | zahra sadat zeynolabedin


حسین باقری | hossein bagheri


نشانی اینترنتی http://drj.mui.ac.ir/index.php/drj/article/view/1684
فایل مقاله فایلی برای مقاله ذخیره نشده است
کد مقاله (doi)
زبان مقاله منتشر شده en
موضوعات مقاله منتشر شده
نوع مقاله منتشر شده Original Article(s)
برگشت به: صفحه اول پایگاه   |   نسخه مرتبط   |   نشریه مرتبط   |   فهرست نشریات